KYMCO Downtown 300i ABS Скачать руководство пользователя страница 132

Страница: 132 / 263

12. COOLING SYSTEM

12-8

Downtown 300i ABS

WATER PUMP

MECHANICAL SEAL (WATER SEAL)
INSPECTION

Inspect the telltale hole for signs of
mechanical seal coolant leakage.

If the mechanical seal is leaking, remove
the right crankcase cover and replace the
mechanical seal.

WATER PUMP/IMPELLER REMOVAL

Remove the coolant inlet hose and outlet
hose.
Remove four bolts and the water pump
cover, gasket and 2 dowel pins.
Remove the water pump impeller.

Inspect the mechanical (water) seal and
seal washer if wear or damage.

The impeller has left hand threads.

＊

The mechanical seal and seal washer
must be replace as a set.

＊

Water Pump Cover

Right Crankcase Cover

Telltale Hole

Water Pump

Seal Washer (Porcelain)

Impeller

Mechanical (Water) Seal

Water pump shaft

Содержание Downtown 300i ABS








































































































































































































































































Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Бренды по названию

Популярные бренды

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Бренды по названию

Популярные бренды