manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 133

12. COOLING SYSTEM

     

12-9

Downtown 300i ABS

WATER PUMP SHAFT REMOVAL

Disconnect the water hose from the right
crankcase cover.
Remove bolts attaching the right crankcase
cover.
Remove the water pump bearing snap ring
from the water pump assembly.

Remove the water pump shaft and inner

bearing.

Remove the water pump shaft outer

bearing.

MECHANICAL SEAL REPLACEMENT

Drive the mechanical seal out of the water
pump assembly from the inside.

WATER PUMP SHAFT INSTALLATION

Drive a new water pump shaft outer bearing

into the water pump assembly from the

inside.
Install the water pump shaft and shaft inner

bearing into the waster pump assembly.

Install the snap ring to secure the inner

bearing properly.

Mechanical Seal

Snap Ring

Water Pump Shaft

Apply sealant to the right crankcase
cover of a new mechanical seal and then
drive in the mechanical seal.

＊

Water Pump Shaft

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды