KYMCO Downtown 300i ABS Скачать руководство пользователя страница 66

Страница: 66 / 263

5. ENGINE REMOVAL/INSTALLATION

5-5

Downtown 300i ABS

Remove the engine mount nut and pull it out.
Remove the engine from the frame.

Torque

: 6.5 kgf-m (65 N-m)

INSTALLATION

Installation is in the reverse order of removal.

After installation, inspect and adjust the
following:

•

Throttle grip free play

•

Fill the cooling system with coolant and

start the engine to bleed air from the system.

API/ABV Reset (Refer to chapter14, page 17)

At removing the engine, be careful not
to catch your hand or finger between
the engine hanger and crankcase.

＊

Mount Nut

Содержание Downtown 300i ABS








































































































































































































































































Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Бренды по названию

Популярные бренды

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Бренды по названию

Популярные бренды