manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 134

12. COOLING SYSTEM

 

12-10

Downtown 300i ABS

Install the dowel pins and a new gasket and
then install the water pump assembly to the
right crankcase cover.
Tighten 12 bolts to secure the right
crankcase cover.

WATER PUMP/IMPELLER
INSTALLATION

When the mechanical seal is replaced, a

new seal washer must be installed to the

impeller.

Install the impeller onto the water pump
shaft.

Torque

: 1.0~1.4 kgf-m (11.8 N-m)

Install two dowel pins and a new gasket.
Install the water pump cover and tighten the
4 bolts.

Torque

: 1.0~1.4 kgf-m (11.8 N-m)

When installing the water pump
assembly, aligning the groove on the
water pump shaft with the tab on the oil
pump shaft.

＊

The impeller has left hand threads.

＊

Seal Washer (Porcelain)

Impeller

Mechanical (Water) Seal

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды