manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 62

5. ENGINE REMOVAL/INSTALLATION

5-1

Downtown 300i ABS

SERVICE INFORMATION

GENERAL INSTRUCTIONS

•

A floor jack or other adjustable support is required to support and maneuver the engine. Be
careful not to damage the scooter body, cables and wires during engine removal.

•

Use shop towels to protect the scooter body during engine removal.

•

Drain the coolant before removing the engine.

•

After the engine is installed, fill the cooling system with coolant and be sure to bleed air from the
water jacket. Start the engine to check for coolant leaks.

•

Before removing the engine, the rear brake caliper must be removed first. Be careful not to bend
or twist the brake fluid tube.

SPECIFICATIONS

Engine oil capacity: 

       

At disassembly: 1.5 L 

    At change: 1.3 L 

Coolant capacity:

    Radiator:

766 cc

    Hose with cool coolant:

169 cc

    Hose with hot coolant:

194 cc

    Reserve tank:

590 cc

    Total capacity:                         1719 cc

   

TORQUE VALUES

90304-GHE8-0040      Engine hanger (Engine side)  

5.0 kgf-m (50 N-m)

90305-LBD4-9000      Engine hanger (Frame side)   

6.5 kgf-m (65 N-m)

95801-10060           Rear fork mount bolts

  

3.5 kgf-m (35 N-m)

90305-KFW6-9120-M1    Rear axle nut

12.0 kgf-m (120 N-m)

95801-10035-00        Rear cushion lower/upper mount bolts 4.0 kgf-m (40 N-m)

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды