manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 136

12. COOLING SYSTEM

 

12-12

Downtown 300i ABS

THERMOSTAT

THERMOSTAT REMOVAL

Remove the met-in box and carrier.
Remove the body cover, center cover and
rear
fender cover A.
Drain the coolant.
Disconnect the thermosensor wire from the
thermosensor.
Disconnect the water hose from the
thermostat housing.
Disconnect the air vent tube from the
thermostat housing.
Remove the mounting bolt and the
thermostat housing from the cylinder head.

Remove two bolts and separate the
thermostat housing halves.
Remove the thermostat from the thermostat
housing.

THERMOSTAT INSPECTION

Suspend the thermostat in a pan of water
over a burner and gradually raise the water
temperature to check its operation.

Technical Data

  Begins to open

71 

℃

  Full-open

80 

℃

  Valve lift

3.5

～

4.5mm

THERMOSTAT INSTALLATION

Fill the cooling system with the specified
coolant.

•

Do not make the thermostat touch the
pan as it will give a false reading.

•

Replace the thermostat if the valve
stays open at room temperature.

•

 Test the thermostat after it is opened

for about 5 minutes and holds the
temperature at 70

℃

.

＊

Replace the O-ring with a new one and
apply grease to it.

＊

Thermostat

Thermometer

Thermostat

Thermosensor Wire

Bolts

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды