manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 2

Downtown 300i ABS

PREFACE

This Service Manual describes the
technical features and servicing
procedures for the KYMCO

Downtown 300i

   

ABS

Section 1 contains the precautions for
all operations stated in this manual.
Read them carefully before any
operation is started.

Section 2 is the removal/installation
procedures for the frame covers which
are subject to removal/installation
frequency during maintenance and
servicing operations.

Section 3 describes the inspection/
adjustment procedures, safety rules
and service information for each part,
starting from periodic maintenance.

Sections 5 to 12 give instructions for
disassembly, assembly and
adjustment of engine parts. Section 13
is the AFI system. Section 14 to 15 is
the removal/ installation of chassis.
Section 16 to 19 states the testing and
measuring methods of electrical
equipment.

Most sections start with an assembly
or system illustration and
troubleshooting for the section. The
subsequent pages give detailed
procedures for the section.

KWANG YANG MOTOR CO., LTD.

QUALITY TECHNOLOGY DEPT.

EDUCATION SECTION

TABLE OF CONTENTS

GENERAL INFORMATION

1

EXHAUST MUFFLER/FRAME

COVERS

2

INSPECTION/ADJUSTMENT

3

LUBRICATION SYSTEM

4

ENGINE REMOVAL/INSTALLATION

5

CYLINDER HEAD/VALVES

6

CYLINDER/PISTON

7

DRIVE AND DRIVEN PULLEYS/V-

BELT

8

FINAL REDUCTION

9

A.C. GENERATOR/STARTER

CLUTCH

10

CRANKCASE/CRANKSHAFT

11

COOLING SYSTEM

12

FUEL INJECTION SYSTEM

13

STEERING HANDLEBAR/FRONT

WHEEL/FRONT BRAKE/FRONT

SHOCK ABSORBER/FRONT FORK

14

REAR BRAKE/REAR FORK/REAR

WHEEL/REAR SHOCK ABSORBER`

15

BATTERY/CHARGING SYSTEM

16

IGNITION SYSTEM

17

STARTING SYSTEM

18

LIGHTS SWITCHES / FUEL PUMP

19

EVAPORATIVE  EMISSION CONTROL

SYSTEM

20

ABS

ANTI-LOCK BRAKE SYSTEM

21

The information and contents
included in this manual may be
different from the motorcycle in case
specifications are changed.

CHASSIS

ELE

C

TRI

C

AL

EQUIPMENT

ENGINE

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды