manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 128

12. COOLING SYSTEM

 

12-4

Downtown 300i ABS

COOLING SYSTEM TESTING
RADIATOR CAP INSPECTION

Install the radiator cap onto the radiator
tester and apply specified pressure to it. It
must hold specified pressure for at least six
seconds.

Radiator Cap Relief Pressure:
    0.9

±

0.15 kg/cm

²

Install the radiator tester onto the radiator
and apply specified pressure to it. It must
hold specified pressure for at least six
seconds.
Check the water hoses and connectors for
leaks.

RADIATOR

RADIATOR INSPECTION

Remove the front cover. 

Apply water to the sealing cap surface
before testing.

＊

Radiator Cap

Radiator Tester

The test pressure should not exceed
1.05 kg/cm

²

.  Excessive pressure can

damage the radiator and its hose
connectors.

＊

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды