manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию, Страница: 75 / 263

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 75

6. CYLINDER HEAD/VALVES

6-7

Downtown 300i ABS

Remove two nuts attaching to the
upper/lower side of cylinder head.
Remove two bolts attaching to the cylinder
head.
Remove the cylinder head.

Remove the dowel pins and cylinder head
gasket.
Remove the cam chain guide.
Remove all gasket material from the cylinder
head mating surface.

CYLINDER HEAD DISASSEMBLY

Remove the valve spring cotters, retainers,
springs, spring seats and valve stem seals
using a valve spring compressor.

Valve spring compressor E040

Remove carbon deposits from the exhaust
port and combustion chamber.

•

Be sure to compress the valve springs
with a valve spring compressor.

•

Mark all disassembled parts to ensure
correct reassembly.

＊

Be careful not to drop any gasket
material into the engine.

＊

Special

Dowel pins

Cylinder Head Gasket

Cam Chain Guide

Valve Spring Compressor

Nut

Bolts

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов