manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 129

12. COOLING SYSTEM

     

12-5

Downtown 300i ABS

Inspect the radiator soldered joints and
seams for leaks.
Blow dirt out from between core fins with
compressed air. If insects are clogging the
radiator, wash them off. Carefully straighten
any bent fins.

RADIATOR REMOVAL

 

Drain the coolant. 
Disconnect the outlet tube of the reserve
tank.

Remove the overflow tube clamp and
disconnect the overflow tube.
Disconnect the air vent tube from the
radiator filler.
Disconnect the fan motor wire coupler.

Loosen the hose band and disconnect the
upper hose and lower hose from the
radiator.

Disconnect the thermostatic switch wire
coupler.

Air Vent Tube

Overflow Tube

Thermostatic Switch

Radiator

Outlet Tube of Reserve Tank

Outlet Tube of Reserve Tank

Outlet Tube of Reserve Tank

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды