manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 160

  13. FUEL INJECTION SYSTEM

     

13-23

Downtown 300i ABS

O

2

 SENSOR

The O

2

 sensor issues signal to ECU when

the temperature is over 350°C during the
engine is working.
The temperature is up to 350°C earlier than
the muffler for O

2

 heater sensor. So the O

2

sensor begins performance.
The function of O

2

 sensor only controls the

fuel injector operation.

INSPECTION

Disconnect the O

2

 sensor connector.

Measure the resistance between each White
wire terminals of the O

2

 sensor side

connector.

Standard:

 7.7±1.2 

Ω

 (at 20°C/68°F)

REMOVAL/INSTALLATION

Disconnect the O

2

 sensor connector and then

remove it from exhaust muffler.

Installation is in the reverse order of removal.

Tighten the O

2

 sensor to specified torque.

Torque: 

2.5 kgf-m (25 N-m, 18 lbf-ft)

Apply anti-seize compound on the surface
of thread area before O

2

 sensor

＊

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды