manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 183

14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/

FRONT SHOCK ABSORBER/STEERING STEM

14-3

Downtown 300i ABS

HANDLEBAR

REMOVAL

Remove the lower handlebar cover and front
cover.

Remove two bolts and disconnect the brake
light switch wire, then remove the rear brake
master cylinder.

Remove the two bolts and disconnect the
brake light switch wire, then remove the front
brake master cylinder.

Remove the inner cover.

Remove the handlebar lock nut and take out
the bolt.
Remove the handlebar and collar.

INSTALLATION

Install the handlebar onto the steering stem
and install the handlebar collar, lock nut and
bolt.
Tighten the bolt to the specified torque.

Torque

: 4.5 kgf-m (45 N-m, 32 lbf-ft)

Brake Light
Switch Wire

Front Light
Switch Wire

Lock nut

Bolt

Collar

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды