manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 47

3. INSPECTION/ADJUSTMENT

 

3-6

Downtown 300i ABS

AIR CLEANER

AIR FILTER REPLACEMENT

Remove the body cover.
Remove seven screws attaching to the air
cleaner cover.
Remove six screws attaching to the filter.
Check the filter and replace it if it is
excessively dirty or damaged.

CHANGE INTERVAL

More frequent replacement is required when
riding in unusually dusty or rainy areas.

SPARK PLUG

Remove the spark plug cap and spark plug.
Check the spark plug for wear and fouling
deposits.
Clean any fouling deposits with a spark plug
cleaner or a wire brush.

Specified Spark Plug

:  NGK-CR7E

Measure the spark plug gap.

Spark Plug Gap

: 0.6 – 0.7 mm

Torque

:17.2 N-m

The air cleaner element has a viscous
type paper element.  Do not clean it
with compressed air.

Be sure to install the air cleaner
element and cover securely.

＊

When installing, first screw in the spark
plug by hand and then tighten it with a
spark plug wrench.

＊

Air Cleaner Cover

Deformation

0.6~0.7 mm

｝

Gap
Wear
Fouling
Deposits

Cracks
Damage

Spark Plug

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды