manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 152

  13. FUEL INJECTION SYSTEM

     

13-15

Downtown 300i ABS

REMOVAL

Disconnect the connector and fuel band from
the fuel pump.
Remove the six screws onto the fuel pump.
Remove the fuel pump and O-ring.

INSTALLATION

Replace a new O-ring on the fuel tank.
Don’t damage the fuel pump wire and
ensure the connector rearward carefully.

Torque: 

0.35 kgf-m (3.5 N-m, 2.5 lbf-ft)

FUEL OUTPUT PRESSURE
INSPECTIION

Turn the key to the OFF position.
Use the fuel hose clamp.
Disconnect the fuel hose from the fuel
injector.
Connect the fuel pressure gauge.
Turn the key to the ON position.
Check the fuel pressure.

Standard:3.0 Bar

Fuel Pump Connector

Hose band

Connector

Screw

O-ring

If the fuel output pressure is less than 3.0
bar, may fail to start the engine or in
trouble in case of riding.

＊

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды