Korg M3, Руководство по параметрам

Страница: 299 / 647

Sequencer: Menu Command Step Recording (Loop Type)
289
11. Press the OK button.
12. When you play back after executing these commands,
the effect on track 3 will change to 032: Stereo Flanger
at measure 9.
13. If you press the COMPARE switch (it will light) and
play back, the playback will occur as it did before you
executed Put Effect Setting to Track.
14. In the P6: Track Edit– Track Edit page, set Track Select
to Track 03, and choose the Event Edit menu command
to access the event edit screen. (In the Set Event Filters
dialog box, check Exclusive.)
Notice that a MIDI parameter change system exclusive
message is inserted at the beginning and at measure 9 of
track 3.
2) Using the song’s own effect settings from the beginning
of the song, and inserting effect settings from elsewhere
into the middle of the song
In this example, we’ll apply an insert effect (IFX3) to MIDI
track 3, and make settings so that it uses 035: Stereo Phaser
from the beginning of the song. At measure 9, we’ll insert a
MIDI parameter change system exclusive message to make
IFX3 switch to the 032: Stereo Flanger effect settings that
were created for a different song.
1. Select a desired program for MIDI track 3, and send it
to IFX3.
Make the following settings for MIDI track 3.
Track Select : Track 03 (P0)
Bus Select (IFX/Indiv.Out Assign) : IFX3 (P8)
In the P0–1: Play/REC– Program T01–08/T09–16 page,
assign a program to track 3. Then use the P8: Insert Effect
page to route track 3 to the effect, and make effect settings.
2. Use Track Select to select Track 03, and record on it.
3. On a separate song you copied, make the effect settings
that you want start using at measure 9.
1) Create song S001.
2) Use the Copy From Song menu command to copy from
S000.
In song 001, make the effect settings that you want to use
from measure 9. Go to the P8–1: IFX– Insert FX Setup, and
choose 032: Stereo Flanger for IFX3.
In the P8–1: IFX– IFX3, set the parameters as desired.
4. Select “Put Effect Setting to Track” to open the dialog
box.
5. Insert the effect settings you created in song 001 into
song 000.
6. Press the OK button to execute the command.
7. After execution, select song 000 and play it back. The
effect for track 3 will change to 032: Stereo Flanger at
measure 9.
8. In song 000, you can press the COMPARE switch (it
will light) and play back to hear the song as it was
before you executed Put Effect Setting to Track.
You can use the COMPARE switch to compare the state of
the track before and after execution.
Note: In the P6: Track Edit– Track Edit page of song 000, set
Track Select
to Track 03 and choose the Event Edit menu
command to access the Event Edit screen. (In the Set Event
Filters dialog box, check Exclusive.)
Notice that a MIDI parameter change system exclusive
message is inserted at measure 9 of track 3.
Step Recording (Loop Type)
Here you can perform step recording into a pattern.
This is available when a user pattern is selected.
1. In Pattern and Pattern Select, specify the pattern.
By default, the pattern length is one measure. If you wish to
change the number of measures in the pattern, set the
Pattern Parameter
.
2. Select “Step Recording (Loop Type)” to open the dialog
box.
3. The remaining steps are the same as when step record-
ing on a track.
Refer to steps 3 and following in Step Recording (see “Step
Recording” on page 279). However, step recording a pattern
differs from step recording a track in that when you reach
the end of the pattern, you will return to the beginning and
continue recording, in this way continuing to add more
data.
Event Edit
Here you can edit individual events of the musical data in a
pattern.
Use Pattern and Pattern Select to specify the pattern, and
then select this command.
The remaining steps are the same as when Event Editing a
track. For more information, please see “Event Edit” on
page 280.
Pattern Parameter
This command specifies the number of measures and the
time signature of the selected pattern.
1. Use Pattern and Pattern Select to specify the pattern.
2. Select “Pattern Parameter” to open the dialog box.
3. In Length, specify the number of measures in the pat-
tern.
Measure : 009
Beat.Tick : 01.000
Effect : IFX3
To: Song: 000
Track : 03
Measure : 009
Beat.Tick : 01.000
Note number
Location within the
measure (beat, clock) Length
(beats, clocks)
Time
signature
Velocity