Korg M3, Руководство по параметрам

Страница: 127 / 647

Program: Menu Command Auto Assign RTC Name
117
11. When the dialog box appears, press the OK button.
The Start Seed parameter will automatically be set to the
internal value needed to reproduce the phrase.
Example: Capture Random Seed has set Start Seed to a value of
+0037783906
Note: Seed is the source data from which the randomizations
are created. The “Seed” of the phrase being looped is
automatically set internally within the KARMA Module as
the Start Seed. The Start Seed is used each time the GE is
triggered. This means that each time you trigger the GE, a
specific Seed is always used to generate the phrase.
12. Press the KARMA ON/OFF switch to temporarily turn
off the KARMA function. Then press the KARMA ON/
OFF switch once again to turn the KARMA function
back on.
13. In the same way as in step 2, use the pad or keyboard to
trigger the KARMA Module.
The phrase that was looped in step 12 will be reproduced
each time the module is triggered. You can now save the
Program and recall this phrase at any time.
Auto Assign RTC Name
This command is available on the KARMA GE tab or
KARMA RTC of the Play page, and the Name/Note Map
tab of the KARMA page.
Auto Assign KARMA RTC Name will automatically assign
appropriate names to the KARMA Sliders and Switches,
based on the GE Real-Time parameters and Performance
Real-Time parameters to which they are assigned. You can
use this when creating new KARMA function assignments,
or editing existing ones.
The names are selected from a list of 400 options, such as
Rhythm Swing% and Rhythm Complexity.
1. Select “Auto Assign RTC Name” to open the dialog
box.
2. To execute the command, press the OK button. To can-
cel without executing, press the Cancel button.
Please be aware that even with un-edited, factory-
preloaded Programs or Combinations, executing this
command may assign names that are different from
those currently specified.
Copy Insert Effect
Copy Insert Effect is available on all of the IFX pages.
This command copies effects settings from within the
current Program, from other Programs, Combinations, or
Songs, or from the current Sampling mode settings.
To execute the Copy Insert Effect command, press the OK
button. To cancel, press the Cancel button.
If you’re copying from a master effect, the result will
not be identical due to differences in the routing and
level settings of the master effects.
From (Mode) [Program, Combination,
Song, Sampling Mode]
This selects whether you’ll copy from a Program, a
Combination, a Song, or the current Sampling Mode
settings.
From (Bank and Number) [Bank and Number]
For Programs and Combinations, this selects the Bank and
Number from which to copy. When this parameter is
selected, you can also use the front-panel BANK buttons to
select Banks.
(Effects slot select) [IFX 1…5, MFX 1&2, TFX]
Select which of the effects you wish to copy.
You can also copy from a master effect and total effect.
All [check-box]
When this is enabled, the settings of all insert effects (the
contents of the Insert FX page and the effect parameters of
IFX1–5, but not Ctrl Ch) will be copied.
To [IFX 1…5]
This selects the insert effect copy destination.
Post IFX Mixer Settings [check-box]
When this is checked, the Pan, Bus Sel., Ctrl Bus, AUX Bus,
and Sends 1 and 2 settings that follow the copy source insert
effect will also be copied.
When this is not checked, only the effect type and its
parameters will be copied.
Copying 000: No Effect
Copying a single effect set to “000: No Effect” will not work:
no data will be copied.
If either All or All used is selected, and “000: No Effect”
exists within a chain, it will be copied. However, if the entire
chain consists of “000: No Effect,” nothing will be copied.