Keysight Technologies N5221A Скачать руководство пользователя

Страница: 60 / 368

3-32 Keysight N5221A/22A Service Guide

Tests and Adjustments
Performance Tests

The output power is measured, and the value is compared to the Preset

setting.

This process is repeated at hundreds of frequencies across the analyzer’s

full range. The difference between the measured power and the output

setting must fall within the specified accuracy range at all points for the

test to pass.

If the Analyzer Fails this Test:

— Perform the

“Source Adjustment” on page 3-42

and repeat this test.

— If the analyzer still fails this test, troubleshoot the source section of the

analyzer and then repeat this test. Refer to

“Checking the Source Group” on

page 4-34

Source Maximum Power Output Test

Function of the Test: To confirm the maximum source output power of your

network analyzer over its full frequency range.
Specification Tested: Test Port Output–Maximum Leveled Power
Equipment Used:

— Power meter
— Power sensors
— Any necessary adapters
Description of the Test:

The analyzer is Preset.

The analyzer is set up for a CW reflection measurement on the test port to

be measured.

A power sensor is connected to the test port, using any necessary

adapters.

The analyzer frequency is set to the desired value.

The power meter correction table is set to the same frequency.

The analyzer’s output power is increased until a “Source Unleveled” error

is detected. The output power is then decreased in increments of 0.01 dB

until the error goes away. if the output power r18 dBm without

any error, the power is left at this level.

The power level at this point is measured and compared to the maximum

output power specification.

This process is repeated at hundreds of frequencies across the analyzer’s

full range in every specified path configuration.

If the Analyzer Fails this Test:

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды