Keysight Technologies N5221A Скачать руководство пользователя | Manualshive

Страница: 99 / 368

background image

Keysight N5221A/22A Service Guide 4-25

Troubleshooting
Rear Panel Troubleshooting

If the analyzer can talk to the network, but the network can not talk to the

analyzer, then the computer or device used from the network may have a

subnet mask that excludes communication with the IP address chosen for the

analyzer. Any subnet mask other than

0.0.0.0

will exclude operation from

some addresses. Changing the subnet mask of a computer or other device

should only be attempted by a qualified network administrator. Failure to

communicate due to a subnet mask incompatibility does not indicate any

failure of the analyzer.
If the analyzer fails to ping in either direction, and assuming the subnet masks

are set properly, then the fault must be isolated to the analyzer or to the

network. Contact a qualified network administrator.

Testing Between Two Analyzers

The ability of the analyzer's LAN to function can be easily tested by connecting

two analyzers together using a “crossover cable” (a short length of cable with

an RJ-45 connector on each end).
Some network hubs have the capability to make a crossover connection using

two normal, or straight-through, cables. If this capability is not available and a

crossover cable is not available, a crossover cable can be made by following

the directions in

“Constructing a Crossover Cable” on page 4-25

Set the IP addresses on two analyzers. The addresses can be set to anything,

but they must be different. Make sure the subnet mask and gateway addresses

are set to

0.0.0.0

and that the LAN is active on both analyzers. Connect the

two analyzers together using either a crossover cable or a crossover hub.
Now follow the steps in

“How to Ping from the Analyzer to the Local Area

Network (LAN)” on page 4-23

to have the first analyzer ping the second

analyzer. When done, repeat the procedure having the second analyzer ping

the first. If both procedures function properly, the LAN circuitry on both

analyzers is verified.
If neither function properly:

— One or both IP addresses could be wrong.
— One or both LAN states could be set to off.
— The crossover cable could be miswired.
— One or both analyzers could be defective.
If possible, eliminate the possibility of a defective analyzer by substitution of a

known working unit. Once the analyzer has been proven to be working

properly, concentration can be placed on the network itself to determine the

cause of the failure.

Constructing a Crossover Cable

A crossover cable can be made from a standard LAN cable by connecting pin 1

from each connector to pin 3 of the other connector, and pin 2 from each

connector to pin 6 of the other connector.

«
...
97
98
99
100
101
...
»

Содержание N5221A

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для N5221A

Бренд: ABB Страницы: 8

Бренд: Kawai Страницы: 5

Бренд: Jata hogar Страницы: 12

Бренд: E-line Страницы: 164

Бренд: Kane Страницы: 20

Бренд: Hach Страницы: 28

Бренд: NARDA Страницы: 64

Бренд: T&D Страницы: 2

Бренд: T&D Страницы: 2

Бренд: jenway Страницы: 52

Бренд: Yamaha Страницы: 6

Бренд: Sage Страницы: 68

Бренд: +GF+ Страницы: 64

Бренд: +GF+ Страницы: 12

Бренд: +GF+ Страницы: 48

Бренд: Hanna Instruments Страницы: 28

Бренд: Sper scientific Страницы: 56

Бренд: S+S Regeltechnik Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды