Keysight Technologies N5221A Скачать руководство пользователя

Страница: 80 / 368

4-6 Keysight N5221A/22A Service Guide

Troubleshooting
Getting Started with Troubleshooting

Getting Started with Troubleshooting

Where you begin troubleshooting depends upon the symptoms of the failure.

Start by checking the basics as outlined in the following section. Also review

the flowchart in

Figure 4-1 on page 4-7

. You should then be able to determine

where in the troubleshooting procedure to begin, to locate the failed assembly.

Check the Basics

A problem can often be solved by repeating the procedure you were following

when the problem occurred. Before calling Keysight Technologies or returning

the instrument for service, please perform the following checks:

Is there power at the mains receptacle? If not, correct this situation and

proceed.

Is the instrument turned on? Check to see if the front panel line switch

glows. This indicates the power supply is on. If the front panel line switch

is on but the power supply does not appear to be on, go to

“Power Up

Troubleshooting” on page 4-8

Is the Windows® operating system running? If not, refer to

“Operating

System Recovery”

Chapter 8

for instructions.

If other equipment, cables, and connectors are being used with the

instrument, make sure they are clean, connected properly and operating

correctly.

Review the procedure for the measurement being performed when the

problem appeared. Are all the settings correct? If not, correct them.

If the instrument is not functioning as expected, return the unit to a known
state by pressing the UTILITY

key.

Is the measurement being performed, and the results that are expected,

within the specifications and capabilities of the instrument? Refer to the

embedded help in the analyzer for instrument specifications.

If the problem is thought to be due to firmware, check to see if the

instrument has the latest firmware before starting the troubleshooting

procedure. Refer to

“Firmware Upgrades”

Chapter 8

for instructions.

If the necessary test equipment is available, perform the operator’s check

and system verification in

Chapter 3, “Tests and Adjustments.”

Troubleshooting Organization

Follow the flowgraph in

Figure 4-1

to help direct you to the correct section for

troubleshooting the analyzer.

Preset

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды