Keysight Technologies N5221A Скачать руководство пользователя

Страница: 66 / 368

3-38 Keysight N5221A/22A Service Guide

Tests and Adjustments
Performance Tests

10.

The corrected noise floor in dBm is calculated for a 10 Hz IF bandwidth

using: PNoiseFloor = Ptest – 19.96 dB – (Preset Power – Pref).

If the Analyzer Fails this Test:

— If the analyzer fails this test, replace the A23 mixer brick for a Port 1 or Port

2 failure or the A24 mixer brick for a Port 3 or Port 4 failure, then repeat this

test. Refer to

“Removing and Replacing the A23 and A24 Mixer Bricks” on

page 7-37

— If the analyzer still fails this test, replace the A12 SPAM board and then

repeat this test. Refer to

“Removing and Replacing the A4–A13 Boards” on

page 7-15

Calibration Coefficients Test

Function of the Test: To verify the uncorrected calibration coefficients of your

analyzer. The calibration coefficients are specified at the test port without any

cables, so calibrations must be performed in both the forward and reverse

directions to eliminate the effects of the test cable.
Specification Tested: Uncorrected System Performance
Equipment Used:

— Calibration kit
— Test cable
Description of the Test:
Two full SOLT 2-port calibrations are performed on each port pair. Ports 1 and

2 are tested as a pair. Ports 3 and 4 are tested as a pair on 4-port analyzers.

Isolation is turned off during each calibration.

A test cable is connected to Port 1.

A calibration is performed between the end of the test cable and Port 2.

The Port 2 directivity and source match and the S21 load match are

retrieved from the analyzer.

The test cable is moved to Port 2.

A calibration is performed between the end of the test cable and Port 1.

The Port 1directivity and source match and the S12 load match are

retrieved from the analyzer.

On some older analyzer models, the reflection tracking and transmission

tracking error terms were also specified. For those models, these error

terms are also retrieved from the analyzer.

This process is repeated for Ports 3 and 4 on 4-port analyzers.

If the Analyzer Fails this Test:

— Failure of the directivity error term is often due to a faulty test port coupler.

Replace the coupler and repeat this test.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды