Keysight Technologies N5221A Скачать руководство пользователя

Страница: 279 / 368

Keysight N5221A/22A Service Guide 7-15

Repair and Replacement Procedures
Removing and Replacing the A4–A13 Boards

Removing and Replacing the A4–A13 Boards

Tools Required

— T-10 TORX driver (torque to 9 in-lb or 1.02 N.m)

— T-20 TORX driver (torque to 21 in-lb or 2.38 N.m)

— ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-6

for this procedure.

Disconnect the power cord.

Remove the outer and inner covers. Refer to

“Removing the Covers” on

page 7-6

A5 and A10 source boards:

A10 source board only: on the bottom side of the analyzer,
disconnect the cables from the A12 and A13 boards (item

①

A5 source board only: on the top side of the analyzer, disconnect all

visible semirigid cables from the other boards.

On the top side of the analyzer, remove two screws (item

➁

), one at

each end of the board, from the source board to be removed.

Lift the two extractors (item

③

), one at each end of the board.

Adjust the slack in the gray flexible cable as needed to move it out

of the way, and lift the board out of the chassis.

A4, A10, A11, A12, and A13 boards:

Remove all cables connected to the top of the board to be removed.

Note the location of each cable for reinstallation.

Lift the two extractors (item

③

), one at each end of the board, and

lift the board.

Before removing the board completely, check the bottom of the

board for any attached cables.

Replacement Procedure

Reverse the order of the removal procedure.

Remember to connect any necessary cables to the bottom of the board

before reinstalling it.

When replacing the A5 or A8 source board, remove the semirigid cables

attached to the bottom of the old board and attach them to the bottom of

the new board. Be sure to orient these cables the same as they were on

the old board.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды