Keysight Technologies N5221A Скачать руководство пользователя

Страница: 316 / 368

7-52 Keysight N5221A/22A Service Guide

Repair and Replacement Procedures
Removing and Replacing the Rear Panel

Removing and Replacing the Rear Panel

Tools Required

— T-10 TORX driver (torque to 9 in-lb or 1.02 N.m)
— T-20 TORX driver (torque to 21 in-lb or 2.38 N.m)
— ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-24

for this procedure.

Disconnect the power cord.

Remove the outer and inner covers. Refer to

“Removing the Covers” on

page 7-6

Remove the A16 power supply assembly. Refer to

“Removing and

Replacing the A16 Power Supply Assembly” on page 7-23

Remove the A17 CPU board assembly. Refer to

“Removing and Replacing

the A17 CPU Board Assembly” on page 7-25

Remove the short (item

①

) and the 50 ohm load(s) (item

➁

Remove the connector hardware (item

③

) from each of the five multi-pin

connectors. The hardware is not the same on each connector so note

which hardware goes with which connector.

Remove the connector hardware (item

④

) from each of the RF connectors.

The hardware is not the same on each connector so note which hardware

goes with which connector.

Remove the 13 screws (item

⑤

) that attach the rear panel to the chassis.

Slide the rear panel over the cable connectors and off of the analyzer.

Replacement Procedure

Reverse the order of the removal procedure.

Perform the post-repair adjustments, verifications, and performance tests

that pertain to this removal procedure. Refer to

Table 7-2 on page 7-60

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды