Keysight Technologies N5221A Скачать руководство пользователя

Страница: 289 / 368

Keysight N5221A/22A Service Guide 7-25

Repair and Replacement Procedures
Removing and Replacing the A17 CPU Board Assembly

Removing and Replacing the A17 CPU Board Assembly

Tools Required

— T-10 TORX driver (torque to 9 in-lb or 1.02 N.m)
— T-20 TORX driver (torque to 21 in-lb or 2.38 N.m)
— ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-10

for this procedure.

Disconnect the power cord.

It is

not

necessary to remove the instrument cover(s) to remove the A17

CPU board assembly.

Remove six screws (item

①

) from the A17 CPU board assembly; four from

the CPU assembly rear panel and two from the ejector handles.

Grasp the two ejector handles and rotate them outward toward the sides

of the analyzer as shown in the illustration. This will disengage the A17

CPU board assembly from the A15 midplane board.

Slide the A17 CPU board assembly out the rear of the analyzer.

If the older 1.6 GHz CPU board is being replaced with the new 2.0 GHz

CPU board, a new A51 solid state drive assembly must also be installed.

Refer to

“Removing and Replacing the A51 Solid State Drive (SSD)” on

page 7-50

If the N5221/22A already had a 2.0 GHz CPU board installed, remove the

A51 solid state drive assembly from the old CPU board and install it in the

new CPU board. Refer to

“Removing and Replacing the A51 Solid State

Drive (SSD)” on page 7-50

Replacement Procedure

Reverse the order of the removal procedure.

Perform the post-repair adjustments, verifications, and performance tests

that pertain to this removal procedure. Refer to

Table 7-2 on page 7-60

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды