Keysight Technologies N5221A Скачать руководство пользователя

Страница: 85 / 368

Keysight N5221A/22A Service Guide 4-11

Troubleshooting
Power Up Troubleshooting

If All Supply Voltages are Present

If all of the supplies have measured within tolerances, and the instrument still

is not functioning properly, refer to

“Front Panel Troubleshooting” on

page 4-16

If Any Supply Voltage Is Missing

You must sequentially remove all of the assemblies, taking care to disconnect

the line power cord before each removal, and then measure the supply

voltages after each removal.
If the missing supply voltages return to a “power on” condition after removal of

an assembly, suspect that assembly as being defective.
Remove the network analyzer assemblies in the order specified in the following

steps (refer to

Chapter 7

for removal instructions).

If any one individual voltage supply from the A16 power supply develops

an over-voltage or over-current problem, all supplies are affected. The

cause of the over-voltage or over-current condition can be the A16 power

supply itself, or any assembly to which the A16 power supply provides

voltage. To isolate the cause, continue to the assembly removal process as

described in the section titled

“If Any Supply Voltage Is Missing” on

page 4-11

Table 4-1

Power Supply Measurement Points

Test Point

Supply Name

Expected Level

(Vdc)

Test Point

Supply Name

Expected Level

(Vdc)

TP517

Analog Ground

0 V

TP516

−

5.2 V analog

−

5.2 ±0.1

TP509

+15 V analog

15.0 ±0.1

TP514

−

7 V analog

−

7.0 ±0.1

TP511

+9 V analog

.0 ±0.1

TP500

Digital Ground

TP515

+3.3 V analog

+3.3 ±0.1

TP502

+5.1 V standby

+5.1 ±0.1

TP513

+5.2 V analog

+5.2 ±0.1

TP503

+12 V digital

+12.0 ±0.1

TP501

+15 V standby

+15.0 ±0.1

TP507

+3.35 V digital

+3.35 ±0.1

TP504

+32 V analog

+32.0 ±0.1

TP505

+5.1 V digital

+5.1 ±0.1

TP512

−

15 V analog

−

15.0 ±0.1

TP519

Digital Ground

0 V

Disconnect the line-power cord before removing any assembly.

Procedures described in this document may be performed with

power supplied to the product while protective covers are removed.

Energy available at many points may, if contacted, result in personal

injury or loss of life.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды