Keysight Technologies N5221A Скачать руководство пользователя страница 275

Страница: 275 / 368

Keysight N5221A/22A Service Guide 7-11

Repair and Replacement Procedures
Removing and Replacing the A1–A3 and Other Front Panel Subassemblies

Disconnect the touchscreen controller board cable (item

④

) from the

touchscreen controller board and front panel interface board.

Disconnect the flat flex cable from the touchscreen.

Remove two screws (item

⑩

) and remove the touchscreen controller

board.

Removing the Power Switch Board and Power Button Keypad

Disconnect the power switch cable (item

⑤

) from the power switch board.

Remove two screws (item

⑩

) and remove the power switch board.

The power button keypad can now be removed from the power switch

board by gently pulling each of the rubber tabs through the PC board.

Figure 7-3

Front Panel Subassemblies Removal

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Keysight Technologies N5221A, Руководство по обслуживанию, Страница: 275 / 368

Результаты поиска

Содержание N5221A

Отзывы: