Keysight Technologies N5221A Скачать руководство пользователя страница 120

Страница: 120 / 368

4-46 Keysight N5221A/22A Service Guide

Troubleshooting
Measurement System Troubleshooting

—

Receiver A; W59

—

Receiver R1; W60

—

Receiver R2; W61

—

Receiver B; W62

—

4-port models

—

Receiver A; W59

—

Receiver B; W60

—

Receiver C; W61

—

Receiver D; W62

—

Receiver R; W63

Disconnect the appropriate flexible RF cable from the output receiver to be

tested on the A20 IF multiplexer board.

Connect the spectrum analyzer to the open connector.

Refer to Note on

page 4-28

. The measured signal on the spectrum

analyzer should be at 7.61 MHz (analyzers with DSP version 4.0), or 7.44

MHz (analyzers with DSP version 5.0).

If the measured signal is present, replace the A12 SPAM board. Refer to

“Removing and Replacing the A4–A13 Boards” on page 7-15

If the measured signal is not present replace the A20 IF multiplexer board.

Refer to

“Removing and Replacing the A20 IF Multiplexer Board” on

page 7-31

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Keysight Technologies N5221A, Руководство по обслуживанию, Страница: 120 / 368

Результаты поиска

Содержание N5221A

Отзывы: