Keysight Technologies N5221A Скачать руководство пользователя

Страница: 82 / 368

4-8 Keysight N5221A/22A Service Guide

Troubleshooting
Power Up Troubleshooting

Power Up Troubleshooting

Check your network analyzer for evidence that it is powering up correctly.

Perform the following steps and make sure that the analyzer is displaying

correct behavior as noted in the following steps.

Step 1.

Disconnect all peripherals and plug in the network analyzer. Before the

analyzer is powered on, the line switch should glow yellow and no other

lights should be on.

Step 2.

Turn on the network analyzer.

• The line switch should glow green.

• The fans should be audible.

• The display should flash and then show the hardware boot-up sequence.

This process checks the RAM and communication with the hard disk drive.

These checks return an error message if a problem is detected.

• The Windows operating system should start.

• The network analyzer measurement interface should open with an S

measurement displayed.

Step 3.

If the analyzer powers up correctly, continue troubleshooting with

“Front

Panel Troubleshooting” on page 4-16

Step 4.

If the analyzer does not power up correctly, follow these troubleshooting

steps:

— If the line switch does not glow, go to

“Power Supply Check” on page 4-9

— If you cannot hear the fans operating, go to

“If the Fans Are Not Operating”

on page 4-13

— If the line switch glows green and the fans are operating (audible), but the

display remains dark, go to

“Troubleshooting LCD Display Problems” on

page 4-14

— If the instrument appears to abort the network analyzer measurement

interface process, contact Keysight. Refer to

“Contacting Keysight” on

page 2-7

Immediately unplug the instrument from the ac power line if the unit

shows any of the following symptoms:

— Smoke, arcing, or unusual noise from inside the analyzer.
— A circuit breaker or fuse on the main ac power line opens.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды