Keysight Technologies N5221A Скачать руководство пользователя страница 86

Страница: 86 / 368

4-12 Keysight N5221A/22A Service Guide

Troubleshooting
Power Up Troubleshooting

Unplug the A19 test set motherboard ribbon cable from the A19 test set

motherboard (refer to

“Removing and Replacing the A19 Test Set

Motherboard” on page 7-29

Unplug the A19 test set motherboard to A20 IF multiplexer board ribbon

cable from the A20 IF multiplexer board (refer to

“Removing and Replacing

the A20 IF Multiplexer Board” on page 7-31

Unplug the front panel interface cable from the A1 front panel interface

board (refer to

“Removing the A1 Front Panel Interface Board and Keypad

Assembly” on page 7-10

Remove the A12 SPAM board (refer to

“Removing and Replacing the A4–

A13 Boards” on page 7-15

Remove the A8 source board (refer to

“Removing and Replacing the A4–

A13 Boards” on page 7-15

Remove the A5 source board, if present (refer to

“Removing and Replacing

the A4–A13 Boards” on page 7-15

Remove the A11 13.5 GHz synthesizer board (refer to

“Removing and

Replacing the A4–A13 Boards” on page 7-15

Remove the A13 13.5 GHz synthesizer board (refer to

“Removing and

Replacing the A4–A13 Boards” on page 7-15

Remove the A4 13.5 GHz synthesizer board, if present (refer to

“Removing

and Replacing the A4–A13 Boards” on page 7-15

)

10.

Remove the A10 frequency reference board (refer to

“Removing and

Replacing the A4–A13 Boards” on page 7-15

11.

Remove the A18 GPIB board (refer to

“Removing and Replacing the A18

GPIB Board” on page 7-27

). Reinstall the A16 power supply assembly and

the A17 CPU board assembly.

12.

Unplug the A51 hard disk drive from the A17 CPU board (refer to

“Removing and Replacing the A51 Solid State Drive (SSD)” on page 7-50

The minimum required assemblies to power up the analyzer are:

— A16 power supply
— A15 midplane board
— A14 system motherboard
— A17 CPU board
To further isolate the failure in the three remaining assemblies, measure the

resistance (with the power turned off) from the power supply test points to
either ACOM or DCOM.

Make sure that the only assemblies plugged in are the four minimum

required assemblies listed above.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Keysight Technologies N5221A, Руководство по обслуживанию, Страница: 86 / 368

Результаты поиска

Содержание N5221A

Отзывы: