Keysight Technologies N5221A Скачать руководство пользователя

Страница: 97 / 368

Keysight N5221A/22A Service Guide 4-23

Troubleshooting
Rear Panel Troubleshooting

The purpose of this section is to determine if the analyzer's hardware is

functioning properly. While the turn-on self-test verifies some LAN hardware

functionality, it is limited to internal testing only. Incorrect IP addresses will

prevent proper operation. Improper subnet masks may allow only one-way

communication, while improper gateway addresses may exclude outside LAN

access.

Ping Command

The analyzer has the built-in capability of performing a “ping” operation. Ping

will request the analyzer to send a few bytes of information to a specific LAN

device. That device will then signal the analyzer that it has received the

information. The analyzer computes the approximate round trip time of the

communication cycle and displays it. For a full test of two-way

communications, a ping test should be performed in two directions.

— First: you should ping from the analyzer to the local area network.

— Second: you should ping from the local area network to the analyzer.

How to Ping from the Analyzer to the Local Area Network (LAN)

Follow the steps below to verify proper LAN operation (assuming you have a

functioning LAN). If no network LAN is available, see

“Testing Between Two

Analyzers” on page 4-25

Make sure the IP address on the analyzer is set properly and that it is

unique. If unsure how to check the IP address, refer to the embedded help

in the analyzer.

Make sure the subnet mask is

0.0.0.0

. If not, note the current setting (to

allow setting it back later) and then set it to

0.0.0.0

Find and note the IP address of another working LAN device on the same

network. Make sure this device is turned on, connected, and is functioning

properly.

To ping the network device:

If the Windows Desktop is not displayed, press UTILITY

then

, then

to view the Windows

Taskbar menu at the bottom of the display.

On the

Windows Taskbar

menu, click Start, point to

Programs

Accessories,

and then click

Command Prompt.

The command prompt window is displayed.

In the second case, any other network device capable of sending a ping

command could be used, assuming it is connected to the same network.

This could be a computer or even another analyzer.

System

Configure

Control Panel

...

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды