manualshive.com logo in svg

KAESER KOMPRESSOREN SIGMA CONTROL SMART MOBILAIR M82, Руководство пользователя, Страница: 120 / 418

Поделиться
Скачать
KAESER KOMPRESSOREN SIGMA CONTROL SMART MOBILAIR M82 Скачать руководство пользователя страница 120

9.4.2  Working pressure too low

Possible cause

Measure

Where can I get help?
SW

KS

Proportional controller defective. Have repaired or replaced if

necessary.

–

X

Inlet valve not opening or only

opening partially.

Repair or have it replaced if

necessary.

–

X

Pressure gauge indicating incor‐

rect reading.

Have it repaired or replaced if

necessary.

–

X

Safety valve maladjusted and/or

leaking.

Have it repaired or replaced if

necessary.

–

X

Venting valve blowing off.

Check the connections and

function and have it repaired or

replaced as necessary.

–

X

Engine does not run at maxi‐

mum speed (in LOAD mode).

See chapter 9.3

X

X

Engine air filter and/or compres‐

sor air filter clogged.

Clean or change, see chap‐

ters 10.4.2 and 10.6.7.

–

–

Oil separator cartridge heavily

clogged.

Change, see chapter 10.6.6.

–

–

SW = Specialised workshop; KS = KAESER SERVICE

Tab. 83 Fault: working pressure too low

9.4.3  Safety valve blows off

Possible cause

Measure

Where can I get help?
SW

KS

Oil separator cartridge heavily

clogged.

Change, see chapter 10.6.6.

–

–

Inlet valve does not close.

Check the controller, control line

and inlet valve and replace if

necessary.

–

X

Safety valve maladjusted and/or

leaking.

Adjust or have it replaced if nec‐

essary.

–

X

SW = Specialised workshop; KS = KAESER SERVICE

Tab. 84 Fault: safety valve blowing off

9.4.4  Machine overheating

Possible cause

Measure

Where can I get help?
SW

KS

Defective cooling fan.

Have the blades or the complete

fan wheel replaced.

–

X

SW = Specialised workshop; KS = KAESER SERVICE

9

Fault Recognition and Rectification

9.4

Analysing compressor faults and alarms

106

Operator Manual    Portable Rotary Screw Compressor  
MOBILAIR M82  SIGMA CONTROL SMART

No.: 901783 08 USE

Содержание SIGMA CONTROL SMART MOBILAIR M82



































































































































































































































































































































































































































Отзывы:

Нет отзывов