manualshive.com logo in svg

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

ITT GOULDS PUMPS 3296 EZMAG - мощный насос высокого качества. Для установки, эксплуатации и обслуживания необходимо скачать руководство по эксплуатации. Скачайте его бесплатно с нашего сайта. Наслаждайтесь эффективной работой вашего оборудования с помощью этого руководства.

Поделиться
Скачать
background image

5  Commissioning, Startup, Operation, and Shutdown ................................................................................... 37

5.1  Preparation for startup.............................................................................................................................37
5.2  Remove the coupling guard ....................................................................................................................38
5.3  Check the rotation ...................................................................................................................................40
5.4  Check the rotation - Close Coupled ........................................................................................................40
5.5  Couple the pump and driver ....................................................................................................................40

5.5.1  Install the coupling guard ..............................................................................................................41

5.6  Bearing lubrication...................................................................................................................................46

5.6.1  Lubricating-oil requirements..........................................................................................................46
5.6.2  Acceptable oil for lubricating bearings .......................................................................................... 47
5.6.3  Lubricate the bearings with oil.......................................................................................................47
5.6.4  Greased-for-life bearing lubrication............................................................................................... 48

5.7  Pump priming ..........................................................................................................................................48

5.7.1  Prime the pump with the suction supply above the pump............................................................. 48
5.7.2  Prime the pump with the suction supply below the pump ............................................................. 48
5.7.3  Other methods of priming the pump.............................................................................................. 50

5.8  Start the pump.........................................................................................................................................50

5.8.1  Minimum continuous recommended flow...................................................................................... 51

5.9  Pump operation precautions ...................................................................................................................52
5.10  Shut down the pump .............................................................................................................................53
5.11  Make the final alignment of the pump and driver................................................................................... 53

6  Maintenance.....................................................................................................................................................55

6.1  Maintenance schedule ............................................................................................................................55
6.2  Bearing maintenance ..............................................................................................................................56
6.3  Disassembly ............................................................................................................................................56

6.3.1  Disassembly precautions ..............................................................................................................56
6.3.2  Required tools ...............................................................................................................................57
6.3.3  Prepare the pump for disassembly ............................................................................................... 57
6.3.4  Remove the frame assembly and shaft (frame-mounted pump)................................................... 58
6.3.5  Remove the frame assembly and shaft (close-coupled pump) ..................................................... 60
6.3.6  Disassemble the liquid end ...........................................................................................................61

6.4  Pre-assembly inspections .......................................................................................................................64

6.4.1  Replacement guidelines................................................................................................................64
6.4.2  Magnet inspections .......................................................................................................................66
6.4.3  Bearing-frame inspection ..............................................................................................................66
6.4.4  Bearings inspection.......................................................................................................................67
6.4.5  Minimum running clearances ........................................................................................................67

6.5  Reassembly.............................................................................................................................................67

6.5.1  Reassemble the frame assembly and shaft (frame-mounted pumps) .......................................... 67
6.5.2  Reassemble the frame assembly and shaft (close-coupled pumps)............................................. 70
6.5.3  Reassemble the liquid end............................................................................................................71
6.5.4  Complete the pump reassembly ................................................................................................... 74
6.5.5  Bolt torque values .........................................................................................................................75

7  Troubleshooting ..............................................................................................................................................76

7.1  Operation troubleshooting .......................................................................................................................76
7.2  Alignment troubleshooting.......................................................................................................................77

8  Parts Listings and Cross-Sectionals.............................................................................................................78

8.1  Close-coupled S-group (all) and M-group (2 x 3 - 8 only) — stainless steel ........................................... 78

Table of Contents

2

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

RAASM 900 Series Manual preview
900 Series
Бренд: RAASM Страницы: 72
Dakota Digital Odyssey ODYR-25-1 Manual preview
Odyssey ODYR-25-1
Бренд: Dakota Digital Страницы: 8
Thermor Aeromax Piscine 10 Installation And User Manual preview
Aeromax Piscine 10
Бренд: Thermor Страницы: 32
3M Aqua-Pure 3MFF100 Installation And Operating Instructions Manual preview
Aqua-Pure 3MFF100
Бренд: 3M Страницы: 8
BLACKMER MAGNES Series Installation, Operation And Maintenance Instructions preview
MAGNES Series
Бренд: BLACKMER Страницы: 14
Wacker Neuson PS 43703 Operator'S Manual preview
PS 43703
Бренд: Wacker Neuson Страницы: 50
BLACKMER LGL154A Installation, Operation And Maintenance Instructions preview
LGL154A
Бренд: BLACKMER Страницы: 12
SuperFish Pond Clear 5000 Quick Start Manual preview
Pond Clear 5000
Бренд: SuperFish Страницы: 12
salmson MULTI-VE 2G Installation And Starting Instructions preview
MULTI-VE 2G
Бренд: salmson Страницы: 68
York PHG4 Series Installation Manual preview
PHG4 Series
Бренд: York Страницы: 24
Xylem Goulds AquaBoost Advanced Instruction Manual preview
Goulds AquaBoost Advanced
Бренд: Xylem Страницы: 36
A.O. Smith ADMR - 115 Technical Specifications preview
ADMR - 115
Бренд: A.O. Smith Страницы: 6
GDH GDH70-Air Installation And Operating Manual preview
GDH70-Air
Бренд: GDH Страницы: 24
Samoa 560 230 Technical Service Manual preview
560 230
Бренд: Samoa Страницы: 82
ZANSKAR HOTSPRING HSTK5 Manual preview
HOTSPRING HSTK5
Бренд: ZANSKAR Страницы: 19
Aquatight PH20V Installation And User Manual preview
PH20V
Бренд: Aquatight Страницы: 24
KBS mini-Compacta Installation & Operating Manual preview
mini-Compacta
Бренд: KBS Страницы: 86
Little Giant PE-2F-PW Series Quick Start Manual preview
PE-2F-PW Series
Бренд: Little Giant Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды