ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 8 / 100

ELECTRICAL HAZARD:

These are examples of other categories that can occur. They fall under the ordinary hazard levels and
may use complementing symbols:

•

Crush hazard

•

Cutting hazard

•

Arc flash hazard

1.2.2 Environmental safety

The work area

Always keep the station clean to avoid and/or discover emissions.

Waste and emissions regulations

Observe these safety regulations regarding waste and emissions:

•

Appropriately dispose of all waste.

•

Handle and dispose of the processed liquid in compliance with applicable environmental regula-
tions.

•

Clean up all spills in accordance with safety and environmental procedures.

•

Report all environmental emissions to the appropriate authorities.

WARNING:

If the product has been contaminated in any way, such as from toxic chemicals or nuclear radi-
ation, do NOT send the product to ITT until it has been properly decontaminated and advise
ITT of these conditions before returning.

Electrical installation

For electrical installation recycling requirements, consult your local electric utility.

1.2.2.1 Recycling guidelines

Always follow local laws and regulations regarding recycling.

1.2.3 User safety

General safety rules

These safety rules apply:

•

Always keep the work area clean.

•

Pay attention to the risks presented by gas and vapors in the work area.

•

Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards.

•

Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

Safety equipment

Use safety equipment according to the company regulations. Use this safety equipment within the work
area:

1.2 Safety

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды