ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 57 / 100

6 Maintenance

6.1 Maintenance schedule

Maintenance inspections

A maintenance schedule includes these types of inspections:

•

Routine maintenance

•

Routine inspections

•

Three-month inspections

•

Annual inspections

Shorten the inspection intervals appropriately if the pumped fluid is abrasive or corrosive or if the envi-
ronment is classified as potentially explosive.

Routine maintenance

Perform these tasks whenever you perform routine maintenance:

•

Lubricate the bearings.

•

Inspect the seal.

•

Perform a vibration analysis.

•

Monitor the discharge pressure.

•

Monitor the temperature.

Routine inspections

Perform these tasks whenever you check the pump during routine inspections:

•

Check the level and condition of the oil through the sight glass on the bearing frame.

•

Check for unusual noise vibration, and bearing temperatures.

•

Check the pump and piping for leaks.

•

Analyze the vibration.*

NOTICE:

*If equipped, temperature and vibration levels can be retrieved by using your i-ALERT monitor-
ing sensor and app.

Three-month inspections

Perform these tasks every three months:

•

Check that the foundation and the hold-down bolts are tight.

•

Change the oil every three months (2000 operating hours) at minimum.

•

Check the shaft alignment, and realign as required.

Annual inspections

Perform these inspections one time each year:

•

Check the pump capacity.

•

Check the pump pressure.

•

Check the pump power.

6 Maintenance

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды