ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 72 / 100

6.5.2 Reassemble the frame assembly and shaft (close-coupled pumps)

Slide the stub shaft (122A) onto the motor shaft and secure it with the setscrew (222L).

Setscrew (122L)

Stub shaft (380)

Motor-to-adapter hex screw (371)

Close-coupled adapter (503)

Mount the motor adapter (503) onto the motor using hex screws (371).

Mount the drive magnet (740B) onto the stub shaft (122A) so that the driver cams are fully-engag-
ed.

Stub shaft–to-motor setscrew (222L)

Stub shaft (380)

Motor-to-adapter hex screw (371)

Frame-to-adapter hex screw (370B)

Close-coupled adapter (503)

Frame-to-adapter gasket (360W)

Drive carrier assembly (740B)

Drive-to-shaft capscrew (791D), internal tooth lockwasher (382)

Insert the lockwasher (382) and capscrew (791D) in order to secure the magnet to the shaft.

6.5 Reassembly

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды