ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 65 / 100

Impeller nut (304)

Impeller nut O-ring (412A)

Impeller (101)

Distance washer (199)

Intermediate ring spacer (351X)

Impeller key (178)

Place the strap wrench on the impeller and remove the impeller nut (304) and O-ring (412A).

Slide the impeller (101) off the shaft.

10. Remove the impeller key (178), distance washer (199), and gasket (351X).

11. Pull the backplate (444) and bearing cartridge (849) from the shaft.

Backplate (444)

Cartridge-to-backplate hex screw (791E)

Parallel pin (445A)

Driven carrier assembly (740A)

Bearing cartridge assembly (849)

Intermediate ring spacer (351X)

12. Remove the second gasket (351X).
13. Undo the screws (791E) and remove the bearing cartridge (849) from the backplate (444).

The driven magnet assembly (740A) is a two-piece assembly on S-group pumps held with a drive-
key. Item 740A is a single-piece component on M-group pumps with a parallel pin (445A) to drive
the bearing cartridge.

The bearing cartridge (849) is one unit that is replaced completely.

6.3 Disassembly

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды