ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 70 / 100

Only use original spare parts to replace any worn or faulty components. The use of unsuitable
spare parts may cause malfunctions, damage, and injuries as well as void the guarantee.

Do not use a flame to heat bearings. This will damage the bearing surfaces. Do not heat the
bearings above 135°C | 275°F.

Bearing frame (228)

Ball bearing (112)

Drive shaft (122B)

Ball bearing (112)

Install the pre-assembled drive shaft in the bearing frame (228) from the motor side.

Insert the wave washer (529).

Labyrinth oil seal (333)

Bearing frame (228)

End cover gasket (360A)

Wave washer (529)

Frame end cover (109A)

End cover hex screw (370C)

Labyrinth oil seal (332A)

Figure 31: Bearing frame cover and seals

6.5 Reassembly

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды