ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя | Manualshive

Страница: 42 / 100

background image

5.3 Check the rotation

WARNING:

•

Starting the pump in reverse rotation can result in the contact of metal parts, heat genera-
tion, and breach of containment. Ensure correct driver settings prior to starting any pump.

•

Failure to disconnect and lock out driver power may result in serious physical injury or
death. Always disconnect and lock out power to the driver before performing any installa-
tion or maintenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals
(IOM) for specific instructions and recommendations.

1.

Lock out power to the driver.

2.

Make sure that the coupling hubs are fastened securely to the shafts.

3.

Make sure that the coupling spacer is removed.
The pump ships with the coupling spacer removed.

4.

Unlock power to the driver.

5.

Make sure that everyone is clear, and then jog the driver long enough to determine that the direc-
tion of rotation corresponds to the arrow on the bearing housing or close-coupled frame.

6.

Lock out power to the driver.

5.4 Check the rotation - Close Coupled

WARNING:

•

Starting the pump in reverse rotation can result in the contact of metal parts, heat genera-
tion, and breach of containment. Ensure correct driver settings prior to starting any pump.

•

Failure to disconnect and lock out driver power may result in serious physical injury or
death. Always disconnect and lock out power to the driver before performing any installa-
tion or maintenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals
(IOM) for specific instructions and recommendations.

1.

Lock out power to the driver.

2.

Make sure that everyone is clear. Jog the driver momentarily, about a half a second. You should be
able to check motor rotation by observing the motor fan direction. The direction should be the same
as the arrow on the close coupled frame.

3.

Lock out power to the driver.

5.5 Couple the pump and driver

WARNING:

Failure to disconnect and lock out driver power may result in serious physical injury or death.
Always disconnect and lock out power to the driver before performing any installation or main-
tenance tasks.

5.3 Check the rotation

40

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

«
...
40
41
42
43
44
...
»

Содержание GOULDS PUMPS 3296 EZMAG





































































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренд: Waters Страницы: 111

TORNADO 2 Series

Бренд: Larius Страницы: 32

TriScroll 300 Series

Бренд: Varian Страницы: 19

Water Solutions 3098 Series

Бренд: Zoeller Страницы: 4

Aquanot Spin 508

Бренд: Zoeller Страницы: 2

Бренд: Zoeller Страницы: 11

Бренд: Zip Страницы: 18

Бренд: Raymarine Страницы: 24

SunCentric Series

Бренд: Dankoff Solar Страницы: 11

Бренд: Bryant Страницы: 26

Бренд: Wacker Neuson Страницы: 64

T4BD-018K Series

Бренд: Nordyne Страницы: 4

Wilden A2550V Series

Бренд: PSG Страницы: 16

Lunaled Creative Set

Бренд: Oase Страницы: 48

JUNG PUMPEN JP09179/3

Бренд: Pentair Страницы: 42

Бренд: Robur Страницы: 82

Бренд: GEA Страницы: 66

TriScroll 620 Series

Бренд: Agilent Technologies Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды