ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 77 / 100

Frame-to-adapter hex screw (370B)

Frame assembly

Mag drive carrier

Frame-to-adapter gasket (360W)

Adapter

Secure the bearing frame and drive magnet assembly:

a) Place the bearing frame and drive magnet assembly already assembled on the workbench with

the drive magnet facing downwards.

b) Screw a 3/8 in. eyebolt into the end of the drive shaft.

Place the bearing frame assembly onto the adapter using a crane.

d) Screw in the hex screws (370B) in order to secure the bearing frame to the adapter.

e) Turn the drive shaft by hand to make sure that the shaft can rotate freely.

Check by looking into the suction nozzle to make sure the impeller is rotating.

6.5.5 Bolt torque values

NOTICE:

Make sure to tighten in a diametrically opposite sequence.

Description

Group

Dry, ft-lbs (Nm) Standard lube, ft-lbs (Nm)

Adapter to casing screws (370)

S/M (M12)

65 (88)

49 (66)

10 in. & 13 in. M (M16) 161 (219)

120 (164)

Impeller nut (304)

47 (64)

26 (35)

116 (158)

52 (70)

Cartridge to backplate screws (791E) S/M

12 (16)

9 (12)

6.5 Reassembly

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды