ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя | Manualshive

Страница: 54 / 100

background image

Group

Size

3500 rpm

2900 rpm

1750 rpm

1450 rpm

1 x 1½ - 8H

22 (5)

18 (4)

11 (2.5)

9 (2)

1½ x 3 - 8

34 (8)

29 (7)

17 (4)

14 (3)

S/M

2 x 3 - 8

74 (17)

61 (14)

37 (9)

20 (5)

M (8 in.)

3 x 4 - 7

157 (36)

127 (29)

78 (18)

64 (15)

3 x 4 - 8G

159 (36)

129 (30)

79 (18)

65 (15)

M (10 in.)

1 x 2 - 10

21 (5)

13 (3)

9 (2)

7 (2)

1½ x 3 - 10

41.5 (9)

35 (8)

21 (5)

17.5 (4)

2 x 3 - 10

78 (18)

65 (15)

38 (9)

31 (7)

3 x 4 - 10

173 (40)

144 (33)

86 (20)

72 (16)

M (13 in.)

1½ x 3 - 13

53 (12)

44 (10)

26 (6)

22 (5)

5.9 Pump operation precautions

General considerations

WARNING:

•

Risk of serious personal injury or property damage. Dry running may cause rotating parts
within the pump to seize to non-moving parts. Do not run dry.

•

Risk of explosion and serious physical injury. Do not operate pump with blocked system
piping or with suction or discharge valves closed. This can result in rapid heating and va-
porization of pumpage.

•

Starting the pump in reverse rotation can result in the contact of metal parts, heat genera-
tion, and breach of containment. Ensure correct driver settings prior to starting any pump.

NOTICE:

Operation at reduced capacity

WARNING:

•

Risk of breach of containment and equipment damage. Excessive vibration levels can
cause damage to bearings, stuffing box, seal chamber, and/or mechanical seal. Observe
pump for vibration levels, bearing temperature, and excessive noise. If normal levels are
exceeded, shut down and resolve.

•

Risk of explosion and serious physical injury. Do not operate pump with blocked system
piping or with suction or discharge valves closed. This can result in rapid heating and va-
porization of pumpage.

•

Risk of equipment damage and serious physical injury. Heat build-up can cause rotating
parts to score or seize. Observe pump for excessive heat build-up. If normal levels are
exceeded, shut down and resolve.

NOTICE:

Cavitation can cause damage to the internal surfaces of the pump. Ensure net positive suction
head available (NPSH

A

) always exceeds NPSH required (NPSH

3

) as shown on the published

performance curve of the pump.

5.9 Pump operation precautions

52

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

«
...
52
53
54
55
56
...
»

Содержание GOULDS PUMPS 3296 EZMAG





































































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренд: Waterstone Страницы: 6

Бренд: Calpeda Страницы: 16

Бренд: Panasonic Страницы: 100

Aquarea WH-MDF09C3E5

Бренд: Panasonic Страницы: 90

Бренд: Panasonic Страницы: 80

Бренд: salmson Страницы: 16

Бренд: Sanden Страницы: 20

Бренд: CLIVET Страницы: 7

Бренд: Takagi Страницы: 64

Бренд: Annovi Reverberi Страницы: 100

Scalekleen EV9796-01

Бренд: Everpure Страницы: 2

Бренд: Nakayama Страницы: 48

MULTI-HE Series

Бренд: salmson Страницы: 44

AJ 4 Plus 100/57 AUT

Бренд: T.I.P. Страницы: 20

Бренд: Navien Страницы: 60

H Design Series

Бренд: Continental Hydraulics Страницы: 8

Gast 1HAB-25 Shown

Бренд: Idex Страницы: 14

Бренд: Simer Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды