ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 63 / 100

Stub shaft–to-motor setscrew (222L)

Shaft (122A)

Motor-to-adapter hex screw (371)

Frame-to-adapter hex screw (370B)

Close-coupled adapter (503)

Frame-to-adapter gasket (360W)

Drive carrier assembly (740B)

Drive-to-adapter capscrew (791D), internal tooth lockwasher (382)

Remove the hex screws (371) that hold the motor to the motor adapter (503).

Pull the motor adapter (503) off the motor flange.

10. Loosen the setscrew (222L) that holds the stub shaft onto the motor shaft.

11. Remove the stub shaft (122A) from the motor.

6.3.6 Disassemble the liquid end

Remove the hex screws (370) that hold the adapter to the case.

Adapter-to-case hex screw (370)

Frame adapter (108)

Backplate-to-case gasket (351)

Casing (100)

6.3 Disassembly

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды