ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя | Manualshive

Страница: 48 / 100

background image

Driver

Slide to fit

Figure 25: Slide driver-half of coupling guard towards motor

10. Use a nut, a bolt, and two washers to secure the coupling guard halves together.

11. Tighten all nuts on the guard assembly.

5.6 Bearing lubrication

WARNING:

Pumps are shipped without oil. Oil-lubricated anti-friction bearings must be lubricated at the job
site.

Risk of explosive hazard and premature failure from sparks and heat generation.

Ensure bearings are properly lubricated prior to startup.

Lubrication requirements

Pump type

Requirements

Close coupled Close-coupled pumps do not have bearings that require lubrication.
Frame mounted

•

The oil level is measured through the sight glass.

•

The oil level must not fall below the center of the sight glass.

•

An increase in oil level may be noted after startup due to oil circulation within the bearing
frame.

5.6.1 Lubricating-oil requirements

Oil quality requirements

Use a high-quality turbine oil with rust and oxidation inhibitors with rated viscosity shown below at 38°C |
100°F.

Oil requirements based on temperature

For the majority of operating conditions, bearing temperatures run between 49°C | 120°F and 82°C | 180°F,
and you can use an oil of ISO viscosity grade 68 at 38°C | 100°F. If temperatures exceed 82°C | 180°F, refer to
the table for temperature requirements.

Temperature

Oil requirement

Bearing temperatures exceed 82°C | 180°F Use ISO viscosity grade 100. Bearing temperatures are generally

about 11°C | 20°F higher than bearing-housing outer surface tempera-
tures.

5.6 Bearing lubrication

46

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

«
...
46
47
48
49
50
...
»

Содержание GOULDS PUMPS 3296 EZMAG





































































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

PELLEMATIC SmartXS

Бренд: MAINE ENERGY SYSTEMS Страницы: 82

HOT Splash HS40

Бренд: Duratech Страницы: 36

Бренд: ACE INSTRUMENTS Страницы: 3

Бренд: REHOBOT Страницы: 14

Бренд: Wacker Neuson Страницы: 60

CLI U12 SD0F1110 NG B/U

Бренд: Velux Страницы: 56

XCT 7 40VC009-048F-7G-QEE

Бренд: Carrier Страницы: 28

HYDROMATIC HTS33A1

Бренд: Pentair Страницы: 8

Бренд: Rheem Страницы: 1

DAIRY WATER HEATER

Бренд: COTSWOLD Страницы: 2

Бренд: Watts Страницы: 16

Бренд: PFT Страницы: 64

Бренд: Lochinvar Страницы: 20

Бренд: Laars Страницы: 40

Бренд: GE Страницы: 80

Бренд: Xylem Страницы: 36

Бренд: AquaPRO Страницы: 55

Бренд: AMT Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды