ITT GOULDS PUMPS 3296 EZMAG Скачать руководство пользователя

Страница: 73 / 100

Frame-to-adapter hex screw (370B)

Close-coupled adapter (503)

Frame-to-adapter gasket (360W)

Figure 33: Close-coupled pump assembly

6.5.3 Reassemble the liquid end

Insert the bearing cartridge (849) into the backplate (444).

Backplate (444)

Cartridge-to-backplate hex screw (791E)

Bearing cartridge assembly (849)

Rotate the bearing cartridge until all three holes line up and secure with hex screws (791E).
See

6.5.5 Bolt torque values on page 75

For M-group pumps, if the driven carrier pin (445A) in the driven magnet assembly (740A) must be
replaced, then drive in the carrier pin carefully until it protrudes approximately 3.05 mm | 0.12 in.
towards the impeller.

The S-group has a drive key, which is automatically placed into position during installation when in-
stalled.

6.5 Reassembly

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Содержание GOULDS PUMPS 3296 EZMAG





































































































Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3296 EZMAG, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3296 EZMAG

Отзывы:

Похожие инструкции для GOULDS PUMPS 3296 EZMAG

Бренды по названию

Популярные бренды