Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 182

background image

Installing Microsoft Windows NT or Windows 2000

51

Installing the Operating System

The following installation procedures highlight the Windows setup options that you must install to
successfully prepare the operating system for the installation of the RAID Software Suite.

✏

NOTE

For detailed Windows installation procedures, please consult the documentation that came with the
computer system or operating system.

Install the operating system software using one of the scenarios (boot diskettes or CD-ROM) below
that matches the installation method.

Installing Windows with Installation Boot Diskettes

1. Boot from the Windows Installation diskettes to setup Windows.

2. Insert boot diskettes and power up the system.

3. During install let Windows detect the storage devices in the system.

4. When device detection is complete, if the hard drive controller is not detected and listed, press

<S> to specify additional storage devices and install the driver.

5. Continue with the Windows installation.

6. After the operating system is completely installed, go to Chapter 7, Loading StorCon to

complete the installation.

Installing Windows Using the Bootable Windows CD-ROM

✏

✏

✏

✏

NOTE

If the driver for the hard drive controller is on the Windows CD-ROM, then follow prompts and
continue at Chapter 7, Loading StorCon. If you are installing a driver that does not come with the
Windows installation CD-ROM, for example, the Intel RAID Controller SRCU32 driver created in
Chapter 2, then follow the procedure below.

1. Insert the CD-ROM and power up the system. If the drivers for the hard drive controller are

not on the bootable Windows CD-ROM, press <F6> as soon as the initial blue screen appears
to ensure that the driver diskette can be loaded.

2. When device detection is complete, press <S> to specify additional storage devices and then

select “Other.” Insert the Intel RAID Controller SRCU32 diskette into the floppy drive and
continue the installation (see the next section).

«
...
49
50
51
52
53
...
»

Содержание SRCU32 - RAID Controller























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCU32 - RAID Controller

System x3630 M4

Бренд: IBM Страницы: 7

Бренд: Garland Страницы: 4

Бренд: Yamaha Страницы: 4

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Бренд: National Instruments Страницы: 130

Бренд: ETAS Страницы: 82

Developer's Board

Бренд: Sony Ericsson Страницы: 28

Бренд: Alesis Страницы: 11

Бренд: NXP Semiconductors Страницы: 1202

Бренд: Alphacool Страницы: 9

BPN-SAS3-LB16A-N10

Бренд: Supermicro Страницы: 11

Бренд: IBM Страницы: 8

Бренд: RadioLAN Страницы: 24

Бренд: Honeywell Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды