Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 182

background image

Storage Console

101

Table 15. Controller Settings

(continued)

Parameter Alternatives

Description

All Messages

All Intel RAID Controller SRCU32 BIOS warnings and errors are displayed

BIOS Warning
Level

Fatal Errors

Only fatal messages are displayed

Disabled

<Ctrl> + <G> not possible

SETUP from
Flash-RAM

Enabled

<Ctrl> + <G> allowed

Off

<Ctrl> + <G> not displayed at system boot level

Display

On

<Ctrl> + <G> displayed at system boot level

2

The Intel RAID Controller SRCU32 BIOS supports 2 drives under
MS-DOS

Supported
BIOS Drives

7

The Intel RAID Controller SRCU32 BIOS supports 7 drives under
MS-DOS

Enabled

Boot from CD-ROM enabled

CD-ROM Boot

Disabled

Boot from CD-ROM disabled

No test

No test at all

Standard Standard

test

Double scan

Double scan test

Memory Test

Intensive

Intensive test (takes longer)

Off

SCSI termination of the channel Off

On

SCSI termination of the channel On

Chn. SCSI-A
Termination

Auto

SCSI termination according to occupied connectors

SCSI ID

0,1,2,3,4,5,6,7

Possible SCSI IDs for the channel

Firmware Update

The firmware, BIOS and StorCon program of the Intel RAID Controller SRCU32 are stored in
Flash-RAM which is part of the Intel RAID Controller SRCU32 hardware. In contrast to
EPROMs, Flash-RAMs can be reprogrammed many times without the complicated UV-light
erasing procedure. Firmware, BIOS and StorCon are part of the SRC_PFW file. The file has an
extension (for example, SRC_PFW.009) which indicates the version stepping.

✏

NOTE

This option is not available when StorCon is accessing the Intel RAID Controller SRCU32
remotely.

Intelligent Fault Bus

The Intelligent Fault Bus is an older subsystem standard, which is no longer used in modern
subsystems or backplanes. Intel RAID Controller SRCU32’s Ultra/Wide Disk Array Controllers
were the last Intel RAID Controller SRCU32s supporting this standard, sometimes also called
“DEC Fault Bus.”

«
...
99
100
101
102
103
...
»

Содержание SRCU32 - RAID Controller























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCU32 - RAID Controller

Бренд: FabiaTech Страницы: 4

AIE900-XNX Series

Бренд: AXIOMTEK Страницы: 53

FastTrak TX4000

Бренд: Promise Technology Страницы: 76

Бренд: ADTRAN Страницы: 20

X-NUCLEO-EEPRMA1

Бренд: ST Страницы: 22

Бренд: Intel Страницы: 20

Бренд: Extron electronics Страницы: 19

HiGain Line Unit HLU-388

Бренд: PairGain Страницы: 7

Бренд: SIIG Страницы: 8

Бренд: XMOS Страницы: 10

Бренд: AMD Страницы: 10

Бренд: National Datacomm Страницы: 62

Бренд: LSIS Страницы: 39

Бренд: LG Страницы: 13

Бренд: LG Страницы: 56

One:Quick Share

Бренд: LG Страницы: 104

Бренд: LG Страницы: 168

Бренд: LG Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды