Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 182

background image

52

Intel RAID Controller SRCU32 User’s Guide

Upgrading an OS (Windows NT 4.0 to Windows 2000) that is Currently Installed on
a RAID Volume or Single Disk

Before you Begin:

Ensure that the OS is installed on an Intel RAID Controller SRCU32 that is compatible with the
new OS and/or RAID Software Suite that you are about to install. If it is not compatible, then exit
this installation procedure.

Upgrading Windows NT 4.0 to Windows 2000:

1. Before beginning, back up any vital data.

2. If you are not installing a new adapter and you are only upgrading the OS and the RAID

software, go to step 9.

3. If you are installing a new Intel RAID Controller SRCU32, and transferring the OS to that new

adapter, go to step 4.

4. Power off the computer, disconnect all power cords, and remove the computer’s cover to access

the server board.

5. Disconnect the SCSI cable(s), if applicable.

6. Remove the currently installed Intel RAID Controller SRCU32 and insert the new Intel RAID

Controller SRCU32 into an available PCI slot.

7. Connect the SCSI cable, if applicable, to the newly installed Intel RAID Controller SRCU32.

8. Replace the computer’s cover, reconnect all power cords, and reboot the computer.

9. Log into NT with administrative user rights.

10. Insert the Windows 2000 CD-ROM. The Windows 2000 upgrade utility will auto-start. Click

“Yes” to start the upgrade.

11. When

the

Welcome to the Windows 2000 Setup Wizard launches, select “Upgrade to

Windows 2000”

and complete this portion of the upgrade. Windows should auto-reboot. If

not, manually reboot the computer.

12. Leave the Windows 2000 CD-ROM in the CD-ROM drive and let the computer boot up.

DO NOT touch any key when prompted to boot from the CD-ROM. Let the computer boot to
the hard drive to continue the upgrade.

13. When the computer gets to the first blue setup screen, immediately press <F6> to load the

RAID drivers for Windows 2000.

14. When prompted press <S> and insert the Intel RAID Controller SRCU32 Installation diskette

and continue the Windows 2000 upgrade.

15. Setup will complete the text-based portion of the installation and auto-reboot to continue the

GUI portion of the Windows 2000 Upgrade.

16. When the GUI portion of setup completes, the computer will auto-reboot. If it does not

auto-reboot, manually reboot the computer to continue the upgrade.

17. Go to the “Installation to an Existing OS” section

to complete the upgrade.

«
...
50
51
52
53
54
...
»

Содержание SRCU32 - RAID Controller























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCU32 - RAID Controller

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: Parker Страницы: 344

Бренд: PaloAlto Networks Страницы: 3

Бренд: Furuno Страницы: 24

Бренд: Black Box Страницы: 9

Proventia A1204

Бренд: Internet Security Systems Страницы: 42

Бренд: Renesas Страницы: 2

Бренд: XtendLan Страницы: 228

Бренд: QuickLink Страницы: 8

NIC-FC730i-Mb-2-32G

Бренд: H3C Страницы: 37

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: PairGain Страницы: 80

Бренд: Altera Страницы: 40

Бренд: Milesight Страницы: 15

Бренд: Navitar Страницы: 1

Бренд: Digital Audio Corporation Страницы: 164

Бренд: Intellinet Страницы: 32

Бренд: Radio Shack Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды