Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 182

background image

48

Intel RAID Controller SRCU32 User’s Guide

Minimum Software Requirements

Microsoft Windows 2000:

•

RAID Software Suite CD-ROM

•

9 MB of free hard drive space (for the RAID Software Suite)

•

Microsoft Windows 2000 Professional, Server or Advanced Server

•

Intel RAID Controller SRCU32 Installation diskette (one blank high density floppy diskette
may be required to create the installation diskette)

Microsoft Windows NT 4.0:

•

RAID Software Suite CD-ROM

•

9 MB of free hard drive space (for the RAID Software Suite)

•

RAID Driver Installation diskette (one blank high density floppy diskette*

may be required to

create the installation diskette)

•

Microsoft Windows NT 4.0 Workstation*, Server* or Server Enterprise Edition*

* Not supplied

Installing an Operating System onto a RAID Volume or
Single Disk

If you do not have the Intel RAID Controller SRCU32

Installation diskette

for the operating system

that you are installing, create it before continuing. See Chapter 2 for instructions to create this disk.
Also refer to Chapter 2 for instructions to install the Intel RAID Controller SRCU32 and to set up a
RAID volume.

✏

NOTE

Prior to installing Windows NT, disable the Delayed Write Cache of the Intel RAID Controller
SRCU32.

CAUTION

To avoid this problem and prevent the risk of data corruption, the Delayed Write function of the
Intel RAID Controller SRCU32 cache must be disabled during the complete installation. To do so,
use the StorCon program. Choose Advanced Setup, Configure Controller, Controller Settings and
switch the Delayed Write function OFF. After having completed the Windows NT installation,
switch the Delayed Write function ON again.

When you do a warm boot by simultaneously pressing the <Ctrl> + <Alt> + <Del> keys, some PCI
server boards carry out a hard reset of the PCI bus. As a consequence, all expansion cards and
devices that are connected to the PCI bus, including the Intel RAID Controller SRCU32, are reset.
During the installation procedure of Windows NT this anomaly can cause the contents of the Intel
RAID Controller SRCU32 cache RAM to be deleted before the data can be written to the disk(s).
If this happens, the installation cannot be completed correctly. Such a warm boot automatically
takes place after a FAT partition is converted into a NTFS partition at the end of the Windows NT
installation procedure.

«
...
46
47
48
49
50
...
»

Содержание SRCU32 - RAID Controller























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCU32 - RAID Controller

Бренд: Idis Страницы: 31

Бренд: Lanner Страницы: 63

AAA-130SA SERIES

Бренд: Adaptec Страницы: 94

Wireless Connectivity Cape

Бренд: Element14 Страницы: 2

Бренд: NCR Страницы: 15

Бренд: Idis Страницы: 18

Бренд: TANDBERG Страницы: 2

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренд: EVGA Страницы: 3

Quark SoC X1000

Бренд: Galileo Страницы: 20

FiberTwist XGS2420

Бренд: Genexis Страницы: 7

Бренд: Alpine Страницы: 17

RS2BL040 - Raid Controller

Бренд: Intel Страницы: 5

Бренд: Devolo Страницы: 24

Бренд: Accusys Страницы: 12

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 8

AirProtect Enterprise Engine 6100

Бренд: 3Com Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды