Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 38

Страница: 38 / 182

Intel RAID Controller SRCU32 User’s Guide

Install the SDRAM

1. Insert the DIMM into the DIMM connector. Make sure the DIMM clips snap to the close

position. (Supported DIMMs are 64 MB to 256 MB ECC PC133 unbuffered SDRAM
memory).

Install the Intel RAID Controller SRCU32 in the Intel Server Board

Install the Intel RAID Controller SRCU32 into an available PCI slot. Refer to the board
documentation for details. The example below refers to the Intel SCB2 server board.

1. Shut down the computer system.

2. Turn the power off.

3. Insert the Intel RAID controller into an available PCI slot.

Use StorCon to Create a RAID Volume

1. Power on the system and press <Ctrl> + <G> when the screen below appears.

2. The following two messages will appear at the bottom of the screen:

“Intel (R) Storage Console to start after POST”
“Please wait to start Intel (R) Storage Console…”

3. When StorCon starts, it will display the Intel RAID Controller SRCU32 installed in the system.

Press <Enter> to select this controller.

Содержание SRCU32 - RAID Controller























































































































































































Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды

Intel SRCU32 - RAID Controller, Руководство пользователя

Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды