Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 49

Страница: 49 / 182

Installing Microsoft Windows NT or Windows 2000

Figure 10. Controller Settings

Windows 2000 / NT 4.0 Installation Procedures

This document, when referring to Windows 2000 and Windows NT, applies to the following
Windows operating systems unless otherwise noted:

•

Windows 2000 Server, Advanced Server, and Professional

•

Windows NT 4.0 Server, Enterprise Edition, Terminal Server Edition, and Workstation

Installing the OS

The following installation procedures highlight the Windows setup options that you must install
during OS installation to successfully prepare the operating system for the installation of the RAID
Software Suite.

Install the operating system software using one of the scenarios (boot diskettes or CD-ROM) below
that matches the installation method.

✏

NOTE

For detailed Windows installation procedures, please consult the documentation that came with the
computer system or operating system.

Installing Windows Using the Installation Boot Diskettes:

1. During install let Windows detect the storage devices in the system. When device detection is

complete, press <S> to specify additional storage devices.

2. Select Other. Insert the Intel RAID Controller SRCU32 installation diskette for Windows into

the floppy drive, press <Enter>

Содержание SRCU32 - RAID Controller























































































































































































Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды

Intel SRCU32 - RAID Controller, Руководство пользователя

Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды