Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 43

Страница: 43 / 182

Getting Started

Install and Launch the StorCon and Utilities:

1. Insert the Intel RAID Controller SRCU32 Software CD.

2. Select “Install” and follow the on screen instructions to install the StorCon and

utilities. (As necessary, refer to Chapter 7, Loading StorCon, for detailed instructions).

3. Launch the StorCon and/or utilities by clicking on the icons located on the desktop.

Installing Red Hat Linux 7.1

Install Red Hat Linux Server:

1. Boot the system with the Red Hat Linux CD-ROM.

2. At the install prompt, select “linux dd.”

3. When prompted, insert the Red Hat Linux driver diskette.

4. Continue with the Linux OS installation.

Install the Intel RAID Controller SRCU32 StorCon Monitoring Utility:

(As necessary, refer to Chapter 7, Loading StorCon, for detailed instructions).

1. Place the Intel RAID Controller SRCU32 CD-ROM in the CD-ROM drive and mount the

CD-ROM:

$ mount /dev/cdrom /mnt/cdrom

2. Copy the StorCon utility archive to /usr/sbin:

$ cp /mnt/cdrom/linux/install/storcon-2.02.gz /usr/sbin/storcon-2.02.gz

3. Unpack the archive file and rename:

$ gunzip –d /usr/sbin/storcon-2.02.gz

$ mv /usr/sbin/storcon-2.02 /usr/sbin/storcon

4. Launch the StorCon utility by typing “storcon” at any prompt.

5. Select the Linux interface to run the utility locally.

Содержание SRCU32 - RAID Controller























































































































































































Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды

Intel SRCU32 - RAID Controller, Руководство пользователя

Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды