Intel SRCU32 - RAID Controller Скачать руководство пользователя страница 56

Страница: 56 / 182

Intel RAID Controller SRCU32 User’s Guide

General Installation Notes

For detailed hardware requirements, specifications, and installation procedures, specific to the Intel
RAID Controller SRCU32, refer to Chapter 2.

Minimum Hardware Requirements

✏

NOTE

The Intel RAID Controller SRCU32 will work in a 32-bit, 33 or 64 MHz PCI slot; however, a 64-bit
66 MHz slot is recommended for maximum performance.

•

Computer with CD-ROM drive (not attached to the Intel RAID Controller SRCU32).
Computer must be on the supported hardware list (for example, Intel SCB2 server board).

•

One available PCI slot.

See note above.

•

PCI 2.2 compliant System BIOS.

•

SCSI hard drive(s) (the minimum required to meet the desired RAID level).

Minimum Software Requirements

•

RAID Software Suite CD-ROM

•

10 MB of hard drive space

•

RAID Driver Installation Diskette for Linux

•

Linux Red Hat 7.x Installation CD-ROMs

•

Root access on the Linux server

Installing Red Hat Linux 7.x on a RAID Volume
(Host Drive)

To install Red Hat Linux 7.x on to a host drive, first create the appropriate driver disk from the Intel
RAID Controller SRCU32 CD-ROM:

1. In the system BIOS, ensure that the computer is set to boot off of the CD-ROM drive.

2. Place the RAID Software Suite CD-ROM in the CD-ROM drive and boot the system.

3. Select the option to make diskettes.

4. Select Red Hat Linux and the appropriate driver for the system. When driver disk is created,

follow the procedure below to create a host drive to install to.

5. Ensure the Intel RAID Controller SRCU32 is installed in the system and is connected to drives

on which you intend to create a host drive.

6. Boot the system and when prompted press <Ctrl> + <G> to enter StorCon. Create a single host

drive from the selected disks.

7. For more information on creating host drives using the StorCon, see Chapter 7, Configure New

Host Drive.

Содержание SRCU32 - RAID Controller























































































































































































Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды

Intel SRCU32 - RAID Controller, Руководство пользователя

Результаты поиска

Содержание SRCU32 - RAID Controller

Отзывы:

Похожие инструкции для SRCU32 - RAID Controller

Бренды по названию

Популярные бренды